Overview

Kerio Control NG100W and Kerio Control NG300W include an embedded WiFi access point, which provides connectivity for wireless devices such as cell phones, tablets, and laptops.

The Kerio Control WiFi module supports:

• Dual-band antenna, which provides 2.4 or 5 GHz
• Wireless standards 802.11a, b, g, n, and ac
• Authentication: none, WPA, WPA2 (PSK or Enterprise)
• Up to eight wireless networks (SSIDs)

Note: Kerio Control NG100W and Kerio Control NG300W do not include wireless client mode, so you cannot connect your Kerio Control to another WiFi access point.

Solution

Configuring the WiFi access point

To configure the WiFi access point in Kerio Control, select a country, band, and channel (global for all Wifi networks). The band and channel are preconfigured to the fastest options for the selected country.

1. In the administration interface, go to Interfaces and WiFi.
2. Click the WiFi button.
3. In the Country drop-down list, select the country where the hardware device is deployed. Each country has different legislative restrictions for bands and channels, and Kerio Control allows you to set only bands and channels that are permitted in the selected country.
4. In the Band drop-down list, the fastest allowed band is selected by default. If your devices do not support the latest ac (5 GHz) standard, switch the band to another one (a, b, g, or n).
5. In the Channel drop-down list, the fastest channel is selected by default. If your devices do not have a good signal, select a different channel.

Now your WiFi is ready and the settings are common for all Kerio Control SSIDs.

Configuring WiFi networks

Service Set Identifier (SSID) allows you to create different WiFi networks. Because WiFi needs at least one SSID to work. The first SSID KerioControl is configured for you:

• SSID = KerioControl
• It is set up as a network bridge (LAN Switch) so that it is a part of your existing local network and users get IP addresses from the local network range.
• It is set to use WPA2 Enterprise, so your users use their Kerio Control accounts for connecting to the WiFi network.

To use the KerioControl network, select the SSID and click OK.

Creating new SSIDs

1. In the administration interface, go to Interfaces and WiFi.
2. Click the WiFi button.
3. In the WiFi Settings dialog box, click Add.
4. In SSID name, type a name for the network. The SSID identifies the WiFi network. It displays on users' devices, so the name should be short and easy to remember.
5. In the Assigned to drop-down menu, select:
   1. LAN Switch to add WiFi to an existing subnet. Your WiFi network runs in the wireless bridging mode. For more information, please refer to Wireless bridging on Kerio Control NG100W and NG300W.
   2. Standalone to add a different network subnet where users get IP addresses from a different range. For details, see Configuring WiFi guest networks and Configuring Ethernet ports in Kerio Control hardware appliances. If you select this option, you must also configure the TCP/IP settings and DHCP. For details, see Configuring TCP/IP settings in Kerio Control interfaces and DHCP server in Kerio Control.

   Usually, you need one SSID assigned to a LAN switch for your local users and one standalone SSID for a guest network.

6. In the Security drop-down menu, select WPA2 Enterprise for local networks and WPA2 PSK for guest networks. For details, see Supported authentication types.
   
   

To verify that the WiFi network is up and running, go to the Interfaces and WiFi section, and check the status in the Trusted/Local Interfaces group.

Supported authentication types

Troubleshooting

Users from Germany, Netherlands, and Bulgaria should use channels less than 140 for optimal power performance. For further information refer to Using WiFi Channels Above 140 in Kerio Control NG100W and NG300W Models.

Related Articles

Setting up Kerio Control NGW series